Skip to main content

Elimination of abandoned cables

By niveksuhail
Elimination of abandoned cables

Unless indicated by the owner or another agency that unused cables are reserved for future use and the cables are marked accordingly, it is necessary to remove abandoned fiber optic cables (cable ending with a connector and not on other equipment, and that has no identification with a label for future use) as required by the National Electricity Code (NEC) or local codes.

At the choice of the owner of the place, the contractor will also be asked to remove other cables (for example copper or electricity communications). Cable removal consumes more time than installation since each cable must be carefully identified and removed so as not to damage other cables. No cable must be cut to be removed unless it has been properly identified as the cable to be removed. 

All cables must be recycled properly. Most communications cables have value as scrap, not only for copper conductors but also for other metallic elements, including some plastics.

Also Read :  cfot certification

Comments

Post a Comment

Popular posts from this blog

One strand of optical fiber is about the diameter of a human hair

By niveksuhail
As the saying goes, one strand of optical fiber is about the diameter of a human hair.CORNING It’s an amazing idea. Now, copper wires—sometimes called “twisted pair” because they are made of pairs of strands of copper twisted around one another—also carry data and telephone signals to homes and farms in much of rural America. But because of the characteristics of copper as a transmission medium, signals that travel over copper doesn’t have the extraordinary frequency range that light signals do, are subject to interference from other signals, and in general, degrade very quickly over more than a short distance. That’s why if you have a copper-wire DSL (digital subscriber line) subscription, you have to be very close to the phone company’s “central office” to get a download signal into your house. A DSL house is connected to a copper wire, not a fiber-optic cable. fiber optic installer salary Not only can light travel over fiber for hundreds of miles with little attenuation (im...
3 comments
Read more

Journal of ISSN Industrial Engineering Systems

By niveksuhail
Fiber optic structureI (Source: Samuel, 1988)  Core  dan  cladding  temade of silica material, glass,  orPlastic ber bertin qualityggi and free water.  Core   has an index blarger scale of cladding (n1 > n2) to the limit critical, so  it's possiblekan  occurrence of  refractionin  total  (total  internal  reflection ).  Withthereby the light will  always bepropagate in the core  to the ends  of the fibers.  Coating   ( jacket ) worksas the core protector and   cladding of t     ekanan physical outside, made of very plastic material quality  (Zanger,  1991,  Thomas,  1995,  Samuel,1988).   Optical fibergenerally classified medoggy 3 types (Figure 4) (Samuel, 1988): 1. Multimode Step Index ,  with finger-jari core 25 – 60 µm, cladding 50 – 150 µm. 2. Multimode Graded Index ,  with fingers core 10 – 35 µm,...
2 comments
Read more

There are two methods that are used to measure the loss

By niveksuhail
There are two methods that are used to measure the loss by insertion with a light source and power meter, a "connection cable test", also called "single-end loss", according to the TIA FOTP-171 standard, and a "cable network test installed" or "loss of two ends", according to the TIA OFSTP-14 (multimode) and OFSTP-7 (single mode) standard. The difference between the two tests is that the single loss test end uses only a launch cable and tests only the connector attached to the launch cable plus the fiber and any other component in the cable. The single-end test is mainly used to test connection cables or short cables since you can test each connector individually. The two-end loss check uses a launch cable and a receive cable attached to the meter and measures the loss of the connectors at both ends of the cable under test. The single-end check is generally used in connection cables to be able to test the connectors at each end of an indi...
1 comment
Read more