Skip to main content

Fiber Optic Light Source

By niveksuhail

Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.

fiber optic light source
Fiber Optic Light Source Catalogue in PDFpdf catalogue (76.2KB)

This fiber optic light source features compact size and decent appearance, it is small size and light in weight, with high stable output power, large LCD display window and easy operation.
fiber optic installation jobs
Wavelengths (nm) 650 1310/1550 850/1300 (more wavelengths can be optional; the maximum can be four wave)
Emitter Type FP-LD LED ¡¡
Output Power (dBm) 0 -7 -20 ¡¡
Spectral Width (nm) ¡Ü10
Output Stability ¡À0.05dB/15mins; ¡À0.1dB/ 8hours
Modulation Frequencies CW, 2Hz CW, 270Hz, 1KHz, 2KHz
Optical Connector FC universal adaptor FC/PC (Interchangeable FC/SC/ST connectors can be optional)
Power Supply Alkaline Battery (3 AA 1.5V batteries)
Operating Temperature -10~+60
Storage Temperature -25~+70
Dimension (mm) 152X74X26
Weight 180g

Comments

Post a Comment

Popular posts from this blog

One strand of optical fiber is about the diameter of a human hair

By niveksuhail
As the saying goes, one strand of optical fiber is about the diameter of a human hair.CORNING It’s an amazing idea. Now, copper wires—sometimes called “twisted pair” because they are made of pairs of strands of copper twisted around one another—also carry data and telephone signals to homes and farms in much of rural America. But because of the characteristics of copper as a transmission medium, signals that travel over copper doesn’t have the extraordinary frequency range that light signals do, are subject to interference from other signals, and in general, degrade very quickly over more than a short distance. That’s why if you have a copper-wire DSL (digital subscriber line) subscription, you have to be very close to the phone company’s “central office” to get a download signal into your house. A DSL house is connected to a copper wire, not a fiber-optic cable. fiber optic installer salary Not only can light travel over fiber for hundreds of miles with little attenuation (im...
3 comments
Read more

Journal of ISSN Industrial Engineering Systems

By niveksuhail
Fiber optic structureI (Source: Samuel, 1988)  Core  dan  cladding  temade of silica material, glass,  orPlastic ber bertin qualityggi and free water.  Core   has an index blarger scale of cladding (n1 > n2) to the limit critical, so  it's possiblekan  occurrence of  refractionin  total  (total  internal  reflection ).  Withthereby the light will  always bepropagate in the core  to the ends  of the fibers.  Coating   ( jacket ) worksas the core protector and   cladding of t     ekanan physical outside, made of very plastic material quality  (Zanger,  1991,  Thomas,  1995,  Samuel,1988).   Optical fibergenerally classified medoggy 3 types (Figure 4) (Samuel, 1988): 1. Multimode Step Index ,  with finger-jari core 25 – 60 µm, cladding 50 – 150 µm. 2. Multimode Graded Index ,  with fingers core 10 – 35 µm,...
2 comments
Read more

There are two methods that are used to measure the loss

By niveksuhail
There are two methods that are used to measure the loss by insertion with a light source and power meter, a "connection cable test", also called "single-end loss", according to the TIA FOTP-171 standard, and a "cable network test installed" or "loss of two ends", according to the TIA OFSTP-14 (multimode) and OFSTP-7 (single mode) standard. The difference between the two tests is that the single loss test end uses only a launch cable and tests only the connector attached to the launch cable plus the fiber and any other component in the cable. The single-end test is mainly used to test connection cables or short cables since you can test each connector individually. The two-end loss check uses a launch cable and a receive cable attached to the meter and measures the loss of the connectors at both ends of the cable under test. The single-end check is generally used in connection cables to be able to test the connectors at each end of an indi...
1 comment
Read more