Skip to main content

What jacket do you need?

What jacket do you need?

Our duplex cable typically comes in a basic zip-cord style where the two fibers are in their own jackets and those two jackets are seamed together.  You can also get round jacket cable where multiple cables are run inside a single round jacket, often with reinforcers running through it.
fiber optic installer salary
If you are going to be running the cable outdoors or in a conduit where it may be exposed to moisture you will need an Outdoor rated cable.

If the cable is going to be abused in any way, including running along the ground where it might be stepped on or used in a way where it'll be unwound and wound back up repeatedly, armored cable may be required. 

If you want a cable that can be run over by a tank, just mention it, we have something that can handle tanks.

If the cable is in a plenum space, you may need a cable that is plenum rated.  Plenum is an air space above multiple rooms. For instance, in office buildings, it's not unusual for the walls of rooms to only go up as high as the drop ceiling.  If you pop your head above the ceiling, you'll see across many walls and see the ceilings of many rooms.  That area is a plenum area where multiple rooms share a common overhead air space.  The rules for using plenum vary based on local building codes.

Comments

Popular posts from this blog

One strand of optical fiber is about the diameter of a human hair

As the saying goes, one strand of optical fiber is about the diameter of a human hair.CORNING It’s an amazing idea. Now, copper wires—sometimes called “twisted pair” because they are made of pairs of strands of copper twisted around one another—also carry data and telephone signals to homes and farms in much of rural America. But because of the characteristics of copper as a transmission medium, signals that travel over copper doesn’t have the extraordinary frequency range that light signals do, are subject to interference from other signals, and in general, degrade very quickly over more than a short distance. That’s why if you have a copper-wire DSL (digital subscriber line) subscription, you have to be very close to the phone company’s “central office” to get a download signal into your house. A DSL house is connected to a copper wire, not a fiber-optic cable. fiber optic installer salary Not only can light travel over fiber for hundreds of miles with little attenuation (im...

Journal of ISSN Industrial Engineering Systems

Fiber optic structureI (Source: Samuel, 1988)  Core  dan  cladding  temade of silica material, glass,  orPlastic ber bertin qualityggi and free water.  Core   has an index blarger scale of cladding (n1 > n2) to the limit critical, so  it's possiblekan  occurrence of  refractionin  total  (total  internal  reflection ).  Withthereby the light will  always bepropagate in the core  to the ends  of the fibers.  Coating   ( jacket ) worksas the core protector and   cladding of t     ekanan physical outside, made of very plastic material quality  (Zanger,  1991,  Thomas,  1995,  Samuel,1988).   Optical fibergenerally classified medoggy 3 types (Figure 4) (Samuel, 1988): 1. Multimode Step Index ,  with finger-jari core 25 – 60 µm, cladding 50 – 150 µm. 2. Multimode Graded Index ,  with fingers core 10 – 35 µm,...

There are two methods that are used to measure the loss

There are two methods that are used to measure the loss by insertion with a light source and power meter, a "connection cable test", also called "single-end loss", according to the TIA FOTP-171 standard, and a "cable network test installed" or "loss of two ends", according to the TIA OFSTP-14 (multimode) and OFSTP-7 (single mode) standard. The difference between the two tests is that the single loss test end uses only a launch cable and tests only the connector attached to the launch cable plus the fiber and any other component in the cable. The single-end test is mainly used to test connection cables or short cables since you can test each connector individually. The two-end loss check uses a launch cable and a receive cable attached to the meter and measures the loss of the connectors at both ends of the cable under test. The single-end check is generally used in connection cables to be able to test the connectors at each end of an indi...